12V 24V US Circuit Tester Electrical Power Probe AVOmeter Automotive Scan Tools

Description

VDIAGTOOL V200 Circuit Tester Power Probe Electrical System 12V 24V Diagnostic Tool
12V 24V US Circuit Tester Electrical Power Probe AVOmeter Automotive Scan Tools
✔100% Original ✔Car Circuit Tester✔Free shipping√US Stock
VDIAGTOOL V200 Car Circuit Probe Tester is an electrical troubleshooting time-saver
>>>Product Features:
🔶DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz.
🔶
4 working modes
: DC voltage, AC voltage, Resistance and Diode Test.
🔶
Identify voltage and polarity of the circuit.
You can find out whether it is a positive or negative ground circuit and check how many volts is getting.
🔶You can
test continuity of the wires and components
, whether they are attached to or disconnected from the vehicle.
🔶
Test the resistance of various sensors
and issues and compare those values to the factory specifications.
🔶
Activate and test components
in your hands or inside the vehicle by supplying positive or negative circuits to them.
🔶
20FT extension cable
allows you to work on semi trucks, trailers or any other long vehicles.
🔶
Built-in light
enables better working in darker spaces.
4 Working Modes - Simply Switch The Mode Button
>>> ✔️
DC Voltage Test
:
🔶 DC voltage detects the voltage value of the circuit under test with a resolution of 0.1 volt.
>>> ✔️
AC Voltage Test
:
🔶 AC voltage detects the Max. Voltage, the Min. Voltage and Frequency of the circuit under test.
>>> ✔️
Resistance Test
:
🔶 Detect the resistance between the circuit probe tip and auxiliary ground lead.
🔶 Determines whether an electrical circuit is complete or broken and if the resistance of a component matches the manufacturer's specification.
>>> ✔️
Diode Test
:
🔶 Detect the operation of the diode assembly and determine if it is conducting.
🔶 Display the actual forward voltage of the diode when its conducting current.
>>>WARNING:
Applying voltage to some circuits at will damage the electronic components of the vehicle.
Kindly use the vehicle manufacturer's schematics and diagnostic procedures when testing.
>>>NOTE:
When power up this probe tester kit, press the power switch first, then contact the tip with the component, the operation life of power switch will be extended.
This Automotive Power Probe Tester Can Do More Than A Multi meter
>>> ✔️ Locate The Short Circuit:
🔶 In most cases a short circuit wil appear by a blown fuse or an electrical protection device tripping (i.e., a circuit breaker). Use the probe tip to activate and energize each of the fuse contacts. The contact which trips the circuit breaker is the shorted circuit.
>>> ✔️ Check Continuity:
🔶 When this auto circuit tester is in Resistance mode, using the probe tip and the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehide's electrical system.
>>> ✔️ Activate Components:
🔶 Activate and test components in your hands or inside the vehicle by supplying positive or negative circuits to them. Such as car lights, motors, windshield wipers, radiator fans, relay, fuel injector and other on-board electric equipments.
>>> ✔️ Test Trailer Lights:
🔶 When this circuit probe kit is in DC Voltage mode, clip the auxiliary ground lead to the trailerground, probe the contacts at the jack and then apply voltage to the probe tip. This allows you check the function and orientation of the connector and trailer lights.
>>> ✔️ Find The Bad Ground:
🔶 Probe the suspected ground wire or contact with the probe tip. If the circuit breaker tripped, this circuit is more than likely a good ground.
Generate Activation Signals to the Tested Components
>>>The activation test function is designed to generate activation signals to the tested components. Such as car lights, relay, fuel injector, motors and other on-board electric equipments.
>>> ✔️ Activate Components in Your Hand
🔶 When this power probe tester is in DC voltage mode, contact the probe tip with the auxiliary ground lead, the components will be activated in your hand, and test their functions.
🔶 Steps to active the bulb:
1.Press the power switch forward to activate the bulb.
2.Contact the tip to the positive terminal of the bulb.
3.Connect the negative auxiliary clip.
>>> ✔️ Activate Components in The Vehicle
🔶 When this electric circuit tester is in DC Voltage mode, contact the probe tip to the positive terminal of the component, the green LED should light up, indicating continuity with the ground.
🔶  If the green LED went off at that instant or if the circuit breaker tripped, the tool has been overloaded. If the circuit breaker is tripped, wait for 15 seconds to reset the circuit breaker.
>>> This could happen for the following reasons:
1.What you are detecting is a direct ground.
2.The component you are testing is short-circuited.
3.The component is a very high current component (i.e., starter motor).
Troubleshoot the Errors When Extracting DTCs From Vehicles
>>>Once the diagnostic trouble code (DTC) is extracted from the vehicle and you realize that troubleshooting starts with a sensor circuit, you can perform a quick test to verify the code.
>>>Using alternating voltage mode, you can test sensors and signal circuits.
>>>Do you suspect that there is something wrong with your sensor?
1.Go to AC voltage mode and use the probe tip with auxiliary grounding lead.
2.Contact the probe tip with the positive terminal of sensor.
3.LCD reading shall be a sine wave under normal conditions.
4.If the LCD reading is abnormal, the sensor is faulty
Specifications
Display：TFT color display (160 x 128 dpi)
Operating Temperature：0 to 60°C (32 to 140°F)
Storage Temperature: -40 to 70°C (-40 to 185 F°)
External Power：12 or 24V power provided via vehicle battery
Length\Width\Height：28mmmm8mm
Weight:1.2kg
Please Pay Attention!!
To prevent personal injury or damage to vehicles and/or the test Tool, read the instruction manual first and observe the following safety precautions whenever working on a vehicle:
◆ Always perform automotive testing in a safe environment.
◆ Wear eye protection that meets ANSI standards.
◆ Keep clothing, hair, hands, tools, test equipment, etc away from all moving or hot enging parts.
◆ Operate the vehicle in a well ventilated work Area: Exhaust gas are poisonous.
◆ Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
Use ectreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These component create Hazardous voltage when engine is running.
◆ Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
◆ Keep a fire extinguisher suitable for gasoling/chemical/electrical fires nearby.
◆ Don’t connect or disconnect any test equipment while the ignition is on or the enging is running.
◆ Keep the tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test tool, when necessary.
◆ When the power switch in the tool is depressed, battery current/voltage is conducted directly to the tip which may cause sparks when contactiong ground or certain circuits.Therefore the tool should NOT be used around flammables such as gasoline or its vapors. The spark of an energized tool could ignite these vapors. Use the same caution as you would when using an arc welder.
Package List
1 × VDIAGTOOL V200 Electric Circuit Tester
1 × Probe Tip
1 × 20FT Extension Cable
1 × Battery Hookup Clips
1 × Cigarette Lighter Adapter
1 × User's Manual
1 × Protective Case
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
1.We accept
Credit cards、Debit card、Apple Pay、Google Pay、PayPal ect.
payment.
2.Please contact us if you need to use another method to pay.
3.Payment should be made within
7 days
after bidding ends.
4.Otherwise an Unpaid Item case will be opened to you.
5.
We are not responsible for buyers’ local taxes.
6.Please include your special requests in eBay note if there is any.
7.We reserve the final right of selling
Delivery details
Order will be shipped within 1-5 business day after payment confirmed.
We have warehouse in US，HongKong，China warehouse.
From our US warehouse via UPS or DHL eCommerce shipping
Delivery time varies from 2 to 6 business days.
From our Hong Kong warehouse via DHL or FedEx Ground
Delivery time varies from 7 to 21 business days.
From our China warehouse
For US buyers, we use SpeedPAK (Delivery time is 8-15 business days) or express delivery(Delivery time is 7-21 business days) .
For other countries' buyers, we use SpeedPAK  or China Post or Hong Kong Post(Delivery time varies from 10 to 30 business days)or Express delivery(Delivery time is 7-21 business days).
We will ship according to your eBay address.
Please make sure it is correct and include phone number for delivery.
If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem.
Please include your special requests in eBay note if there is any.
Terms of sales
We are authorize distributor, our all items are 100% original and Our devices have warranty,
12 months free repair for the devices.
3 months for the accessories.
Please contact us firstly when you need warranty service.
In case an item arrives faulty, please contact us in 30 days and keep it unused.
We will instruct you on how to return and get refund or replacement.
If after 30 days, or the item has been used, we have the right to decline your claim.
Items should be returned on buyers' cost for repair or replacement.
About us
Who We Are?
We are specialized dealer of On-Board Diagnostic tools and automotive electronics
for more than 10 years.
We are authorized first class distributor of VDIAGTOOL.
What Do We Have?
We have office and warehouse in CN and US to ensure fast shipment and after-sale service.
Terms of tax:
We are not responsible for buyer's local taxes, please consult your local Customs for tax details.
Contact us
Our customer-oriented service strives for positive feedbacks with all 5 star selling ratings.
Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case.
We will reply in 24 business hours.
Business time: GMT8 (9:00-18:00) from Monday to Friday.