PB100 12V 24V Car Electrical Circuit Tester Power probe AVOmeter Diagnostic Tool

Description

1. DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz. 2. Perform current injection, measurement, ground test, polarity test, continuity test and component activation 3. Ergonomic housing design with waterproof, rugged, blow-molded housing, easy to handle and store. 4. There are 4 modes to diagnose the electrical systems.(DC voltage, AC voltage, Resistance, Diode) 5. AC- RMS, AC peak to peak, frequency and pulse width for signal testing. 6. High voltage capability: displays up to 60 volts, 0.1 volt resolution. 7. 8-amp circuit breaker, automatic reset, no button to press. 8. Three additional modes: MIN / MAX / audible monitoring. 9. Automatically detects positive, negative and open circuit.
PB100 12V 24V Car Electrical Circuit Tester Power probe AVOmeter Diagnostic Tool
PB100 Power Probe Kit
Ancel PB100 Power Probe Circuit Tester Automotive Diagnostic Tool 12V 24V Electrical Current Voltage Integrated Power Scanner
Product Properties:
DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz.
Perform current injection, measurement, ground test, polarity test, continuity test and component activation.
Ergonomic housing design with waterproof, rugged, blow-molded housing, easy to handle and store.
There are 4 modes to diagnose the electrical systems.(DC voltage, AC voltage, Resistance, Diode)
AC- RMS, AC peak to peak, frequency and pulse width for signal testing.
High voltage capability: displays up to 60 volts, 0.1 volt resolution.
8-amp circuit breaker, automatic reset, no button to press.
Three additional modes: MIN / MAX / audible monitoring.
Automatically detects positive, negative and open circuit.
Large color screen LCD with easy to navigate user menu.
Comes with an additional 20ft extension cable.
Find shorts to ground and to voltage.
More uses are worth your expectation！
Find The Short Circuits:In most cases, a short circuit will appear as a blown fuse or a tripping of an electrical protection device.Use the probe tip to activate and energize each of the fuse contacts..The contact which trips the circuit breaker is the shorted circuit.
Find The Bad Ground: Probe the suspected ground wire or contact with the probe tip. If the circuit breaker tripped, this circuit is more than likely a good ground.
Testing Trailer Lights: While the tool in DC Voltage mode, clip the auxiliary ground lead to the trailer ground , probe the contacts at the jack and then apply voltage to the probe tip. This lets you check the function and orientation of the connector and trailer lights.
Check Continuity: While the tool is in Resistance mode, using the probe tip with chassis is ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system.
Activating Component: The component activation function is designed to generate activation signals to the tested components, such as activating lights, motors and other on-board electric equipments.
Signal Circuit Testing: Once you extract a DTC from the vehicle and realize that troubleshooting begins with some kind of sensor circuit, there is a quick test you can perform to verify the code. Testing your sensor is easy while using the tool.
Voltage & Polarity Testing: While the tool is in DC Voltage mode, contact the probe tip to a POSITIVE circuit. If contact the probe tip to an OPEN circuit, neither of the LED will light.
ANCEL PB100 Product Function:
1. Work Mode
There are four modes to diagnose the electrical systems,which can be accessed by depressing the Mode Button and cycling through each one.
3. Circuit Continuity Testing in Resistance mode
While the tool is in Resistance mode,using the probe tip with chass is ground or the auxiliary ground lead,continuity can be tested on wires and components attached or disconnected from the vehicle's electrical system.When the probe tip is contacting a good ground,the LCD will indicate"0.0Ω" and green LED wiil be on,A beep tone will sound.
7. Signal Circuit Testing
For example,you suspect there is a problem with your M.A.P.?sensor circuit,then follow the procedure involved with testing this sensor:
Set the tool in AC Voltage mode,using the probe tip with chassis ground or the auxiliary ground lead.
Connect vacuum pump to MAP sensor.
Contact the probe tip to the MAP sensor positive terminal and observe the LCD readings which should be a sine wave in normal condition.
Apply vacuum
Release vacuum and observe the LCD readings
Two power supply methods
Powered by vehicle battery or cigarette lighter, Compared with other circuit testers that only use car battery power, PB100 provides more choices and is more convenient to use.
FAQs
Q: Where can I find the probe tip?
A: We keep the probe above the back of the device. (Warm note: Be more careful when operating because of the sharp probe tip.)
Q: Why can not the probe tip itself stay engaged? It keeps falling out.
A: You need to push it a little harder until you hear a "CLICK" sound, then it will stay engaged.
Q: Why should I buy an ANCEL PB100?
A: Our products are designed to help you save time and money in electrical diagnostics.
Q: Where can I find training videos?
A: You can learn by browsing the video on the page or the YouTube.
Payment
Shipment
About US
Customer Services
Contact us
Payment
-We accept payment via Paypal.
-Payment must be made within 7 days. If you don't make the payment within 7 days, you may received a Non-payment message automatically sent from eBay.
Non-payment may result in an UPI (Unpaid Item), eBay will automatically close your account if you accumulate 4 UPI's total. Total amount due includes the final auction price plus S&H(Shipping and Handling).
-Your package will be out within 1 business day after payment cleared.
Shipment
1.Shipping address supplied by Paypal is acceptable.
2.
All parcels will be send via USPS/USPS priority/UPS/ Expedited Shipping
3. After the payment cleared, your order will be sent out within 1 business days (not including holiday and weekend).
4. If your package delayed few days, due to any unexpected factor, please wait patiently. Your kindly understanding and great patience would be highly appreciated!
5. Any further queries, please don't hesitate to email us. Thank you.
About US
-We are a professional Authorized dealers of
AUTEL, ANCEL, AUTOPHIX, FOXWELL, KZYEE, LAUNCH, NEXAS, Vgate, OBDPROG,OBDSTAR etc
.
Also offer reasonable prices , excellent customer service and a reliable credit standing are our target!
- We supply many products on Automobile consumer.
There are OBDII cars / Light Trucks / Heavy Duty Truck's Diagnostic Tool, Mileage Correction & Key Program tool, Battery Tester, Fuel Injector Cleaner, Digital Circuit Tester, lgnition Spark Tester
and much more others products.
-We are eager to be your professional partner of automobile diagnostic tool.
-We support remote assistance by TeamViewer if you have any difficulty in software installation.
Customer Services
1. Please do not hesitate to leave us your
5 Star ★★★★★ of DSR positive feedback
if you are satisfaction with our products ,delivery or services .
2. If you
have Any Questions Or unsatisfied with your purchase, please email us first to get a better solution
before you leave a neutral or negative feedback
,
we work hard to make sure every customer 100% satisfied and resolve any problem for you.
Thank you for your kindness.
Contact us
1. If you have any further queries, you can feel free to email me via email or eBay message. Thank you.
2. Please email us first
before giving negative feedback or opening a case. Wish we can solve the problem peacefully.
3. Much appreciated if you could leave us positive feedback with five stars.
4. We will reply you within 12 hours and do our best solve the problem with you （Except on Weekends and Holidays） .
Work time:GMT8 (9:00am-18:30 PM) ,Except for Saturday (9:00-11:00AM) .